Your Plumbing Crash Course: Tips for Installing a Bathtub
Your Plumbing Crash Course: Tips for Installing a Bathtub
Blog Article
The publisher is making a number of good observations regarding How to Install a Bathtub overall in the article just below.
Mounting a tub isn't precisely rocket science, yet it does need solid plumbing, woodworking, as well as in some cases, tiling abilities. Replacing an old bathtub with a brand-new one is also a reasonably hard task. If the old tub is conveniently accessible, the job can move speedily; if you have to open up a wall to eliminate the old tub and also place the new tub, the task is much harder. In either instance, the job is within a residence handyman's abilities, although you will need a helper to leave the old tub as well as embeded in the brand-new one. Ensure you have actually certified yourself for the task as well as are comfortable attempting it. Instead of employing a service provider to take control of a halfway-completed task, it is far better to consider using one prior to you begin. Opportunities are you might require an expert plumber to make tube connections.
This article will certainly assist you set up a new bath tub in your shower room if you have currently gotten a new bathtub as well as don't require to alter the setup of your previous water pipes.
Your devices and product checklist ought to consist of the following:
Removing Old Taps
If you require to replace old taps with new ones as a part of your setup, after that the first thing you must do is detach the supply of water. After doing so, switch on the taps to drain pipes any water continuing to be in the system. The process of getting rid of the existing faucets can be rather problematic as a result of the restricted gain access to that is usually the case.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the faucets. Have a fabric ready for the remaining water that will certainly come from the pipes. As soon as the supply pipelines have been removed, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from transforming throughout this process. As soon as the taps have actually been removed, the holes in the bath/basin will need to be cleaned up of any old securing compound.
Prior to going on to fit the new faucets, compare the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly require a plastic connector to prevent damages to the string. One end of the connector fits on the plastic tail of the faucet and the various other end supplies a connection to the existing supply pipes.
If you require to fit a monobloc, after that you will require lowering couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next, position the faucet in the placing opening in the bath/basin making sure that the washers remain in area between the tap and also the sink. Protect the tap in position with the producer provided backnut. When the tap is firmly in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular tap ports. The previous type must be connected to the tap finishes first, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Installing the Tub
Utilizing both wood boards under its feet, position the bath tub in the needed placement. The wooden boards are useful in uniformly spreading out the weight of the tub over the area of the boards as opposed to focusing all the weight onto 4 small points.
The next goal is to make sure that the tub is leveled all round. This can be accomplished by checking the spirit level and adjusting the feet on the bath tub till the level checks out level.
To install faucets, fit all-time low of the furthest versatile tap connector to the appropriate supply pipeline by making a compression sign up with; after that do the exact same for the other faucet.
Activate the supply of water as well as check all joints and new pipework for leaks and also tighten them if required. Fill the bathtub and also check the overflow electrical outlet and also the regular electrical outlet for leaks.
Lastly, take care of the bathroom paneling as explained in the producer's instruction manual. Tiling and sealing around the bath tub needs to wait till the tub has been utilized a minimum of once as this will certainly settle it into its last placement.
Getting ready for the Setup
Firstly, the sustaining framework supplied with the bathroom should be fitted (if called for) according to the producer's guidelines. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is essential to see to it that if the faucet includes a plastic washer, it is fitted between the bath and the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps unit to avoid strain on the bath tub.
Fit the versatile faucet ports to the bottom of both taps making use of 2 nuts and olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet via the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Make sure you utilize all of the supplied washers.
Attach the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath ought to currently be ready to be fitted in its final setting.
Tiling Around the Tub
In the location where the bathroom fulfills the tile, it is essential to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to break a rigid seal, creating the water to pass through the wall surface between the bathroom and the tiling, causing difficulties with wetness as well as feasible leakages to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your components and also fittings. They are sold in tubes and also cartridges, and can securing voids as much as a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill the tub with water prior to sealing, to enable the movement experienced when the tub remains in usage. The sealant can split fairly early if you do not think about this motion prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise quickly readily available on the marketplace. It is advisable to fit the floor tiles making use of water-resistant or waterproof adhesive and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I ran across that post on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround when doing a lookup on the search engines. If you please take a moment to promote this blog post if you appreciated it. Many thanks for your time. Visit again soon.
Immediate relief, just a call. Report this page